Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGhost Controls Gate Repair in Coppell, TX | Ironworks Gate Co.
We provide independent Ghost Controls Gate Repair in Coppell, and the work here has a pattern most pages will not tell you about: the city’s 1985 to 2005 HOA subdivisions are aging in unison, and the original Ghost Controls operators installed in that era are failing in specific, predictable ways tied to Blackland Prairie clay and driveway resurfacing that predates current conduit standards. That means our Coppell calls are less about random breakdowns and more about a generation of equipment reaching the end of its service life at the same time. Ironworks Gate Co. has serviced every major Ghost Controls model line, and we keep diagnostic benches loaded with Ghost Controls control boards and power supplies so we can trace a fault before we ever order a part. If your gate is binding, dead, or reversing for no reason, call (432) 237-4128 and a live person answers, day or night.
Why Coppell Residents Choose Us for Ghost Controls Service
Ghost Controls openers are good equipment, but they are not simple. The difference between a fix that lasts and one that fails again in six weeks often comes down to whether the technician has actually bench-tested the control board before swapping parts. We have. Victor Salinas, our owner, grew up in Grapevine not far from Dove Road, and he learned early that most gate problems trace back to skipped maintenance and motors that were undersized from the start. He brought that habit of looking for the root cause to Ironworks, and it shapes how we serve the Coppell service area. We work on Ghost Controls nearly every week here, mostly in HOA communities where the same three or four opener models repeat house after house. That repetition means our Coppell techs know the failure modes before they open the control box.
We are an independent service provider, not a Ghost Controls authorized dealer, and we are direct about what that means: we install genuine OEM parts when the repair must match HOA approval and part warranty, and we stock high-grade aftermarket equivalents for discontinued components. Every job gets the 90-Day Done Right Promise in writing, with upfront pricing settled before we turn a single bolt.
Common Ghost Controls Gate Repair Problems We Solve in Coppell
- Binding actuator arms from post heave. Coppell sits on expansive clay that swells and shrinks with rain and drought cycles. When a post shifts even half an inch, a Ghost Controls TSS1 arm binds at the clevis pin and shears the attachment bolt. We see this every summer after the clay dries out.
- Dead solar batteries under mature tree canopy. Northlake Woodlands and older streets near Sandy Lake Road have dense live oaks. The OEM solar charge controller on a TSS1XP often cannot hold 12 volts through those shaded weeks, and the opener quits after a stretch of overcast weather. The panel looks fine, the battery is not getting charged.
- Phantom “obstruction detected” faults on AXS2 boards. Humidity and ice-melt spray corrode the terminal strip on Ghost Controls AXS2 control boards. The opener stops and reverses for no visible reason. Cleaning and re-seating the ribbon cable usually clears it, but if left too long the corrosion eats the board.
- Drifting dual-leaf synchronization on ZDS1XP units. Fine chalky clay dust works into one actuator’s internal limit switch, and the secondary leaf starts lagging. The gate still closes, but the auto-close safety loop triggers erratically because the leaves are no longer in sync.
- Severed loop detector wiring under resurfaced driveways. This one is uniquely Coppell. Original 1990s swing-gate installations along Denton Tap Road often had underground sensor conduit poured over when HOAs resurfaced driveways. The motor looks dead, but the real fault is a broken loop wire under the asphalt, found only with a continuity trace from the pedestal.
Ghost Controls Service in Coppell: What Local Conditions Mean for Your Equipment
Coppell developed almost entirely as HOA-governed master-planned subdivisions between the mid-1980s and early 2000s. That is a fact you can verify with any city planning map. What it means for Ghost Controls owners is that the ornamental iron driveway gates and community entry gates installed during that build-out are now 20 to 35 years old, all reaching their mechanical limits at roughly the same time. Hinge failures, operator motor replacements, and post corrosion are not scattered incidents here, they are a wave moving through virtually every neighborhood. The original 1990s-era underground loop detectors and swing-gate operators along Denton Tap Road and Sandy Lake Road were frequently never updated when HOAs resurfaced driveways in the early 2000s. Conduit got cracked, sensor wiring got severed, and what presents as a dead Ghost Controls motor is often a hidden continuity break that a simple motor swap will not fix. A technician who replaces the operator without tracing the loop wire will be back in three weeks with the same dead gate. We trace it first. That is the difference between a repair and a repeat service call, and in Coppell’s uniform housing stock, knowing where to look is half the job. A gate that works right should be the last thing on your mind.
Ghost Controls Models & Products We Service in Coppell
We service the full Ghost Controls lineup that shows up on Coppell driveways: the TSS1 and TSS1XP heavy-duty solar swing openers, the AXS2 and AXS2XP automatic swing gate openers, the ZDS1 and ZDS1XP dual swing gate systems, and the HY-S series sliding gate openers. Our approach on parts is straightforward. We install genuine Ghost Controls OEM control boards, actuators, and remotes whenever the repair must preserve an HOA-approved appearance and a new-part warranty. For discontinued ZDS1 limit switches and older battery trays, we use aftermarket equivalents that meet or exceed the original specification. And we are honest about repair versus replace: any Ghost Controls actuator showing more than 0.020 inches of bushing play is better replaced than rebuilt, because a new arm costs less than two return trips for the same bind. For broader Ghost Controls work outside Coppell, see our Ghost Controls sales & service page.
Ghost Controls Service Pricing in Coppell
What you pay depends on what we find when we open the control box. In Coppell, a Ghost Controls service call that stops at diagnosis and simple repair, a loose wire, a re-seated ribbon cable, a cleaned limit switch, typically runs $95 to $200. Replacing a failed control board or remote receiver lands in the $250 to $450 range depending on the model and board generation. A full actuator replacement on a TSS1 or AXS2 arm, the common fix for a sheared clevis pin, runs $400 to $800 installed. Dual-gate ZDS1 sync work, where both actuators need re-timing and one limit switch replacement, falls between $500 and $900. For every one of those jobs, you get a written quote before any work starts, and the final invoice matches the quote. No surprises. We also honor a permanent 5% senior and veteran discount, and any repair over $250 takes $50 off. Call (432) 237-4128 for a free estimate, and if you have a written estimate from another company, we will give you a free second opinion on it.
Serving Coppell, TX - Our Local Coverage Area
We’re based in the Coppell area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Ghost Controls Gate Repair in Coppell
Your gate post has likely shifted on Coppell’s expansive Blackland Prairie clay after spring rains soaked the soil. The TSS1 arm is now binding at the clevis pin because the post is out of plumb, and the opener’s force sensor stops travel before the motor burns out. The fix is re-plumbing the post or repositioning the mounting bracket, not forcing the motor to push harder. Call (432) 237-4128 and we will confirm the post movement before touching the operator.
In Coppell’s mature tree canopy, especially in Northlake Woodlands, the panel may be in sun for only a few hours a day, and the OEM charge controller often cannot hold 12 volts through that. The battery drains faster than the panel refills it. We test the charge controller output under load, and in many cases the right fix is a higher-output controller paired with a correctly sized battery for your gate’s cycle count, not another OEM panel.
Yes, if the gate’s track and rollers are in sound condition and the post is set in concrete below the frost line. The HY-S series sliding opener is the right Ghost Controls option. We handle our Gate Installation in Coppell, including opener mounting, safety photo eyes, and power run from the nearest exterior outlet or panel. Your HOA may require pre-approval for any visible hardware change, and we can provide the spec sheet for that application.
We will supply the technical documentation, model specs, and finish details your HOA committee needs, but the approval itself comes from your HOA. Most Coppell HOAs approve like-for-like Ghost Controls repairs without a full board review, because the opener is a direct replacement. If the repair changes the gate’s appearance, hardware finish, or operator location, expect a longer review. We are glad to write up the submittal in the format your property manager requires.
Ghost Controls openers integrate cleanly with most aftermarket keypads and intercoms that output a dry contact or relay signal. We land those two wires on the control board’s accessory terminals and you keep your existing entry hardware. The exceptions are proprietary wireless systems from certain 1990s-era intercom brands, which sometimes need a small relay adapter. We will tell you during the estimate whether your existing keypad works or needs an adapter, and the cost of that adapter is included in the written quote. Call (432) 237-4128 for an exact answer on your equipment.
Service Areas Near Coppell
We serve Coppell and the surrounding communities, including Grapevine, Carrollton, Bedford, Irving, and Euless. For homeowners just outside Coppell, see Ghost Controls service in Carrollton or Ghost Controls service in Grapevine. Same crew, same 90-Day Done Right Promise.
Book Your Ghost Controls Service in Coppell Today
Call (432) 237-4128 for a free estimate on any Ghost Controls repair in Coppell. A live person answers 24 hours a day, and we will set a time that works for you. The price is quoted and agreed before any work starts.
Written by Victor Salinas, Owner at Ironworks Gate Co., serving Coppell since 1984.