Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterTrusted Gate Repair for Grapevine Homeowners
A sagging gate, a motor that grinds but won’t move, a hinge that’s pulled loose from the post. These are the calls we answer every day in Grapevine, and most of the time we have the gate working again before lunch with our Best Gate Repair in Grapevine, TX. Ironworks Gate Co. has been repairing driveway and estate gates for over 42 years, and we do it with a straightforward promise: the job is quoted before we start, done right the first time, and backed in writing for 90 days. If your gate is acting up in Grapevine, call (432) 237-4128. A live person answers, day or night.
What Our Gate Repair Service Includes
Gate repair covers the whole assembly: the steel or iron frame, the hinges and posts, the motor and control board, the lock, and the alignment that keeps everything moving true. Here’s what we handle most often with Gate Repair in Grapevine, and what we do about it.
Electric Gate Repair
When an electric gate stops responding to the remote or keypad, the cause is usually in the control board, a limit switch, or a wiring connection that’s worked loose. Grapevine’s heavy clay soil shifts with the seasons, and that movement puts strain on conduit runs and sensor wiring. We troubleshoot the full circuit, not just the obvious component, because a gate that opens on its own or stops halfway is often the result of two or three small faults working together.
Automatic Gate Repair
An automatic gate is a mechanical system: opener, arm, chain or screw drive, safety edges, and photo eyes all have to work in sequence. When one part fails, the others compensate until they can’t. Our technicians are trained on nine opener brands and carry the common OEM parts on the truck, so most automatic gate repairs in Grapevine are finished in a single visit. We test the full open-and-close cycle several times before we leave, and we check the safety reverse every time, without exception.
Hinge & Post Repair
Hinges carry the entire weight of the gate, and when they wear or the post they’re bolted to starts leaning, the gate drags and the opener burns out faster. In Grapevine’s summer heat, steel posts set in concrete can expand and crack the footing, especially on older installations from the 1990s and early 2000s. We re-weld, re-anchor, or replace hinges and posts as needed, and we always check the post depth and footing condition while we’re at it.
Gate Realignment
A gate that scrapes the driveway or won’t latch is out of alignment, and forcing it closed makes everything worse. The frame may have twisted, the hinges may have sagged, or the ground underneath may have settled. Realignment means adjusting the hinges, shimming or re-welding the frame, and re-setting the opener travel limits so the gate closes cleanly every time. It’s one of the most common repairs we do in Grapevine, and one of the most satisfying when a homeowner watches the gate swing free again.
Lock Repair
A gate lock that sticks, rusts, or won’t accept the key is a security problem and a daily frustration. We repair mechanical and electronic locks, replace worn cylinders, and re-key when needed. If the lock is integrated with the opener, we make sure the electronic release still fires correctly after the mechanical repair, so you don’t end up locked out of your own driveway.
Weld & Rust Repair
North Texas is hard on ornamental steel. Summer heat bakes the finish, winter freezes open any crack, and humidity does the rest. Cracked welds at the frame corners, rust-through at the bottom rail, broken pickets: these are structural issues, not cosmetic ones. We cut out the bad metal, weld in new stock, and rust-treat the repair so the patch doesn’t become a new weak point. A gate we repaired in the 1990s is still swinging in Grapevine today, because we did the metalwork the old way: hot, slow, and solid.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Brands We Service for Gate Repair
We service FAAC openers regularly, including the older hydraulic models still running on many Grapevine estates. The 400 and 700 series have their own quirks: pressure relief adjustments, specific oil requirements, and wear patterns that a generalist will chase for hours without solving. We’ve seen enough of them to diagnose most FAAC faults in the first thirty minutes on site.
BFT and Linear units are also common across the metroplex, and we’ve learned their weaknesses the honest way: by fixing hundreds of them. BFT control boards are sensitive to power surges, which matter in Grapevine’s storm season. Linear actuators wear at predictable points, and we know what those parts look like when they’re about to fail. Whether your opener is a Viking, a FAAC, a BFT, a Linear, or something else entirely - including units needing our Gate Repair in Southlake - the diagnosis starts the same way: we listen to the motor, check the voltage, and test the safety circuit before we recommend a single repair.
Signs You Need Gate Repair Right Now
- The gate is dragging or scraping the driveway. This means the hinges or posts are failing, and every cycle is putting additional load on the opener motor. Left alone, a dragging gate turns a $200 hinge repair into a $900 opener replacement.
- The opener runs but the gate doesn’t move. This is often a broken chain, a stripped gear, or a failed drive coupling. The motor is burning electricity and wearing itself out while the gate sits still.
- The gate stops halfway or reverses for no reason. Safety edges and photo eyes can misread an obstruction, or a limit switch may be out of adjustment. Either way, a gate that won’t close reliably is a liability you don’t want.
- There’s visible rust at the bottom rail or weld points. Rust is structural cancer for a steel gate. What you can see on the surface is typically half of what’s underneath, especially on older ornamental gates with box-section frames.
- The gate won’t stay latched or locked. A gate that swings open in the wind or can’t be secured is an invitation to trouble. It also means the frame geometry has shifted, and forcing the latch puts more stress on every joint.
Our Gate Repair Process - Step by Step
We work the way we’d want a tradesman to work at our own homes: show up on time, explain what we’re doing, and leave the place clean. Here’s how a typical repair goes.
- 1
Call and describe the symptom. You call (432) 237-4128, a live person answers, and we ask questions that help us bring the right parts and tools. We serve Grapevine and the surrounding communities every day, so we can usually schedule your visit the same day or next morning.
- 2
On-site diagnosis. The technician tests the power supply, checks the opener, cycles the gate manually, and inspects hinges, posts, safety edges, and the control board. We use a multimeter to verify voltage at the board and a draw test on the motor, because a motor that’s pulling too many amps is a motor that’s about to die. We don’t guess; we measure.
- 3
Written quote, agreed before work starts. We tell you exactly what’s wrong, what it costs to fix, and what your options are. The price is settled before we turn a single bolt. If the repair is over $250, we take $50 off. If you have a written estimate from another company, we’ll give your repair a free second look and a free second opinion.
- 4
The repair itself. Most Grapevine jobs are done in a single visit. We carry OEM parts for the common brands, along with welding gear, steel stock, and a full run of hand tools. The technician won’t leave until the gate cycles correctly, the safety reverse trips properly, and the gate latches square.
- 5
Walkthrough and the 90-Day Done Right Promise. After the repair, we show you exactly what we did and test it in front of you. Every job gets our written 90-day guarantee, which is exactly what it sounds like: if it’s not right, we come back and make it right. No paperwork, no arguing, no exceptions.
How Much Does Gate Repair Cost in Grapevine?
A typical gate repair in Grapevine runs between $150 and $600, depending on what’s actually broken. A simple hinge adjustment or limit switch reset might be $150 to $250. A control board replacement on a FAAC or BFT opener generally lands between $300 and $600 with the part included. Welding a cracked frame or rusted bottom rail typically runs $250 to $800, depending on how much metal needs to be replaced and how accessible the work area is. Full opener replacement, when repair doesn’t make sense, starts around $900 and goes up from there based on the brand and the gate’s weight and length. Several things move the price: the brand of opener, the age of the gate, how accessible the hinges and posts are, and whether we’re working on a single swing gate or a heavier sliding gate. The best way to avoid overpaying is to get a written quote before the work starts and to know exactly what’s included. Our estimates are free, itemized, and binding. You’ll never see a surprise line on the bill, because the price you approve is the price you pay.
Gate Repair Near Grapevine - Our Service Area
We’re based in the Grapevine area and work throughout the mid-cities and surrounding communities: Gate Repair in Coppell, Gate Repair in Carrollton, Bedford, Irving, Euless, Double Oak, Hurst, North Richland Hills, Southlake, Colleyville, and Flower Mound. Most calls in Grapevine get same-day or next-morning service, and the outer parts of our service area are usually reached the following day. We keep our route tight so we can actually show up when we say we will. If you need gate help anywhere in the area, Gate Repair in Grapevine is what we do every day, and our home page tells the full story of how we work for all our local communities.
Serving Grapevine, TX - Our Local Coverage Area
We’re based in the Grapevine area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
Frequently Asked Questions - Gate Repair in Grapevine
Gate repair is the process of diagnosing and fixing any part of a driveway or estate gate that isn’t working correctly: the hinges, posts, frame, lock, opener, control board, or safety devices. In Grapevine, that often means realigning a gate that’s sagging in the shifting clay soil, replacing a control board that’s been fried by a storm surge, or welding steel that’s rusted through after decades in Texas weather. The goal is always the same: a gate that opens when you want it to, closes when you want it to, and stays shut when it should.
Most residential gate repairs in Grapevine are completed in a single visit, usually within one to three hours on site. A hinge adjustment or limit switch reset is often done in under an hour, while a control board or weld repair might take two to three hours. If a part has to be ordered, we’ll tell you exactly what’s coming, when it will arrive, and what the total cost will be before you commit. We keep the most common OEM parts stocked on our trucks so ordering delays are rare.
Most repairs in Grapevine cost between $150 and $600, with simple adjustments at the low end and control board or structural welding work at the high end. The exact price depends on the brand of opener, the age and condition of the gate, and what’s actually broken. We quote every job in writing before we start, so there’s no guesswork and no surprise on the final bill. Call (432) 237-4128 and describe what your gate is doing; we’ll give you an honest range over the phone and a free on-site estimate before any work begins.
Yes. We service FAAC, BFT, Linear, Viking, LiftMaster, Ghost Controls, DoorKing, Elite, and Mighty Mule openers, and we stock common OEM parts for the brands we see most often in Grapevine. FAAC hydraulic units and BFT control boards are two of the most frequent service calls we handle in the area. Whatever brand is on your gate, we’ve likely repaired dozens of them, and if we haven’t, we’ll tell you straight rather than pretend.
In most cases, yes. We keep our service area tight around Grapevine and the surrounding communities so we can respond quickly, and a live person answers our phones 24 hours a day, 7 days a week. An emergency is a gate that won’t close at all, a gate that won’t open, or a gate that’s stuck open and can’t be secured - that’s when you need Emergency Gate Repair in Grapevine, TX. Call (432) 237-4128 and we’ll get a technician headed your way as soon as the route allows.
Every repair we complete is covered by our written 90-Day Done Right Promise. If it’s not right, we come back and make it right, no paperwork, no arguing, no exceptions. Some OEM parts also carry their own manufacturer warranties, and we’ll show you exactly what’s covered and for how long before you pay a dime. We’ve been in business since 1984, and we plan to be here to honor that promise for another forty years.
Clear the area around the gate so we have room to work: move vehicles away from the driveway, trim back any vegetation touching the gate, and make sure the gate’s power source is accessible if you know where it is. If you have a remote or keypad, have them handy so we can test the full system. Don’t force the gate open or closed before we arrive; let it rest where it is. We’ll handle the rest.
Schedule Your Gate Repair Service in Grapevine Today
Your gate is part of your home’s first impression and its last line of security. When it fails, you want it fixed by someone who’s been doing this work in Grapevine for over 42 years and stands behind it in writing. Call (432) 237-4128 for a free, no-obligation estimate. A live person answers, and we’ll give you a straight answer and a fair price before any work begins.
Written by Victor Salinas, Owner at Ironworks Gate Co., serving Grapevine and the surrounding communities since 1984.