Linear Gate Parts & Welding Nationwide

Linear Gate Parts & Welding in Grapevine: What to Know First

Independent Linear gate parts and welding service in Grapevine runs $180 to $1,400 for most hinge, roller, rail, and post repairs, with the majority of jobs completed in one visit. We quote the full price before any work starts, so there are no surprises on the bill. If you own a Linear gate that is dragging, binding, or rusting at the hinges, call us at (432) 237-4128 and we will tell you what is wrong before we touch anything.

Call (432) 237-4128

This page is for Grapevine homeowners with a Linear slide or swing gate who need honest answers about parts, welding, and what it should cost. Whether you have an older Linear actuator still doing its job or a newer model that has started to misbehave, the issue is rarely the motor alone. It is usually the metal under it. That is where we work.

How Linear Products Fail - and How We Fix Them

• Hinge welds cracking on older Linear swing gate arms. The Linear VS-GSLG and similar swing operators put steady stress on the gate leaf hinges. In Grapevine’s clay-heavy soil, posts shift seasonally, and the hinge weld becomes the stress point. We have seen year-old hinge welds crack clean through because the post moved a half inch and the gate kept swinging. Our fix is a full post reset, gusset reinforcement, and a weld that matches the original geometry, not a bead over the crack.
• Roller bearings seizing on Linear slide gates. Linear slide operators like the SL series work fine until the gate rollers underneath stop rolling. Then the motor is dragging dead weight across the rail. Grapevine’s dust and the occasional ice storm do not help. We replace rollers with sealed-bearing units, check the rail for wear, and re-align the gate so the operator is pushing, not fighting.
• Rack and pinion wear on high-cycle Linear slide gates. If your Linear slide gate has been opening and closing multiple times a day for a decade, the rack teeth near the center wear thin. The motor starts to clunk or skip. We inspect the rack, replace worn sections or the full run depending on condition, and set the pinion depth correctly. Skipping a worn rack will kill a Linear operator faster than anything else.
• Actuator mounting plates pulling loose from the post. Linear swing operators bolt to a plate, and that plate is only as good as the welds or anchors holding it to the post. We see plates that were tacked on by an installer in a hurry and have worked loose over five years. The operator is fine; the mount is not. We cut the old plate off, true the post, and weld a new plate square and level before remounting the operator.
• Chain sag and idler pulley failure on Linear chain-driven slide gates. The Linear chain-drive slide operators need proper tension and good pulleys. When a pulley bearing wears out, the chain starts to whip and the gate jerks. Homeowners often think the motor is dying. Half the time it is a $40 pulley and a chain tension adjustment. We replace the worn pulley, set the chain correctly, and save you an operator replacement you did not need.

Our Linear Gate Parts & Welding Process

1. 1
   We listen and look. You call (432) 237-4128 and a live person answers, day or night. We ask what the gate is doing, when it started, and what brand and model you have if you know it.
2. 2
   We inspect on your driveway. A background-checked, uniformed technician arrives and goes over the gate: hinges, rollers, welds, rail, operator mounts, and the opener itself. We explain what is actually wrong before recommending anything.
3. 3
   We price it in writing. You get a firm quote with the exact parts and labor before any work begins. We use OEM Linear parts when warranty or fit calls for it, and honest, proven aftermarket parts when they are the better value. We tell you the difference and let you decide.
4. 4
   We do the work. Welding, replacement, alignment, and testing all happen in one visit for most jobs. We clean the work area when we are finished.
5. 5
   We run the gate through its cycles. Open, close, obstruction test, safety edge check. We verify the operator is not fighting the gate anymore.
6. 6
   You get the 90-Day Done Right Promise. Written, plain, and simple: if it is not right, we come back and make it right.

What Linear Gate Parts & Welding Costs in Grapevine

Here are the ranges we quote in Grapevine for common Linear gate parts and welding jobs:

• Hinge replacement (single gate leaf): $180 to $450 depending on hinge type and post condition
• Gate roller replacement (set of 2-4, slide gate): $220 to $500 including rail inspection and alignment
• Weld repair (cracked hinge, plate, or frame section): $150 to $600 depending on access and extent of the damage
• Post replacement with concrete re-set: $600 to $1,400 for a driveway post in Grapevine’s clay soil, including weld-out and re-mount
• Chain and pulley service (Linear chain-drive slide): $150 to $380 parts and labor

The price moves based on how much steel has to come out, whether the post has shifted, and whether the operator itself is still healthy. We give you the number before we start, and it does not change. Call (432) 237-4128 for a free estimate on your exact gate.

Why Grapevine Homeowners Call Ironworks Gate Co. for Linear Work

We have been working on gates since 1984, and we still treat every job like it is our own driveway. When a Linear gate needs welding or hard parts, we know what the metal is telling us: where the stress is, what moved, and what will fail next if we do not address it now. Owner Victor Salinas learned the trade at Tarrant County College and has spent over twenty years fixing gates across the Grapevine side of the lake, including plenty that other companies gave up on.

We also service the other eight brands we are trained on: LiftMaster, Mighty Mule, Ghost Controls, and DoorKing among them. So if you trade the Linear for something else later, we will still be the call. Every job carries the 90-Day Done Right Promise in writing. A live person answers the phone 24/7. And the price is set before a single bolt is turned. As Victor puts it: “A gate that works right should be the last thing on your mind.”

FAQs