Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Parts & Welding Across Southlake
Gate parts and welding in Southlake, TX usually comes down to one of three jobs: a hinge plate pulling loose from a masonry pillar, a weld cracking on heavy ornamental iron, or a post that has shifted out of plumb. Typical repairs run $220 to $480 for hinge re-anchoring, $180 to $350 for crack repair and re-welding, and $450 to $900 for post replacement with concrete footing work. If your gate is sagging, grinding, or no longer latching square, call our Gate Parts & Welding team at (432) 237-4128 and we will get it right.
We work throughout Southlake, from the estates off Dove Road down to the neighborhoods near Southlake Boulevard and White Chapel Boulevard. Most Southlake gate welding and parts calls are completed in a single visit. We quote the price before we touch a bolt.
Why Ironworks Gate Co. Is Southlake’s Preferred Gate Parts & Welding Company
Southlake gates are not like gates anywhere else in the metroplex. The homes are bigger. The iron is heavier. The pillars are brick and stone, not steel tube posts. That means the failures are different too. A general handyman who fixes a chain-link gate in Bedford is not equipped to re-anchor a 16-foot ornamental swing gate that has pulled its hinge plate 3/8 of an inch out of a brick column in Timarron. We are.
We stock lag-shield anchors, hydraulic cement, and replacement hinge assemblies for the exact failure pattern we see over and over in Southlake: wet-year clay expansion shoving pillars outward, shearing bolts, and cracking mortar joints at the hinge column. Our technicians know what a stripped anchor thread in 30-year-old brick looks like before the gate even comes off the hinge. We bring the right steel, the right rod, and the right welder on the first trip. No second appointment because someone guessed wrong.
Every job we finish in Southlake is covered by our 90-Day Done Right Promise. It is written. It does not require paperwork or arguing. If something we welded, anchored, or replaced fails within 90 days, we come back and make it right. No exceptions. The price is settled before work starts, and a live person answers the phone at (432) 237-4128 any hour, any day.
Our Gate Parts & Welding Services in Southlake
We handle the full scope of Gate Installation - Southlake, gate parts and welding work on Southlake properties. These are the four services that account for most of what we do here:
Hinge Replacement
Heavy ornamental gates in Southlake hang on hinge plates bolted into brick or stone pillars. In this clay soil, those pillars move. Within five to ten years of installation, the top hinge weld often cracks or the anchor bolts pull loose entirely. We cut out the old fasteners, drill for lag-shield anchors, pack the void with hydraulic cement, and weld on a reinforced hinge plate that matches the gate’s existing ironwork profile. When we are done, the gate swings true and the operator stops fighting its own weight.
Post Replacement
When a gate pillar in Southlake has leaned too far or the mortar bed has crumbled beyond patching, the real fix is post replacement, not another shim job. We saw-cut the old post or pillar at the footing, haul it out, and set a new fabricated post or rebuilt masonry column on a fresh concrete footing. Most Southlake gates are anchored to poured-concrete-footed masonry pillars, so we pour new footings at least as deep as the original and let the concrete cure before we re-hang the gate. It takes longer than a patch. It lasts decades, not seasons.
Rail Repair
The bottom rail of a Southlake ornamental gate takes the most punishment: rain splash, irrigation overspray, and road film off the driveway. Builder-grade welds where pickets meet the bottom rail rust through first, and once the rust starts, the crack spreads along the rail. We grind the old weld out, cut back the rotted section, and weld in replacement rail stock before re-attaching pickets with a full penetration weld. If the bottom rail is beyond saving, we fabricate a replacement section to match what is already there.
Custom Welding
Southlake homeowners often want a gate fixed to look like it was never touched, which means custom fabrication, not off-the-shelf parts. We weld replacement operator mounting brackets, fabricate pickets to match existing decorative scrollwork, repair ornamental finials, and reinforce sagging corners with gusset plates hidden inside the frame. We handle both in-shop fabrication for removable gates and on-site MIG and stick work for gates that stay hung during repair. Whatever is on your driveway, we match it.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Southlake
Most Southlake estates run our Gate Motor & Opener in Southlake services on commercial-grade swing operators like the LiftMaster LA500, FAAC models, or older Viking units. We are trained and equipped on all of them, along with Elite and Mighty Mule systems that show up on secondary gates and ranch entrances. Our trucks carry common control boards, limit switches, capacitor kits, and safety photocells for these brands, so we can resolve operator-side issues during the same visit as the welding work. That matters when a hinge repair also requires re-aligning the opener or replacing a cracked control board housing.
Common Gate Parts & Welding Problems We See in Southlake Homes
- Hinge plates pulling free from brick pillars. Expansive Blackland Prairie clay swells after wet seasons and shrinks during drought. That cycle shoves pillars outward, snapping top-hinge welds and stripping anchor threads within a single decade on most Timarron-style brick pillar gates.
- Welds cracking along the bottom rail. Decorative iron pickets rust through where they meet the bottom rail, especially on gates near sprinkler heads or driveway drainage. A mid-rail crack from rust almost always signals deeper rail corrosion that a simple sag-correcting bead cannot save.
- Operator brackets tearing off stone or brick. A gate that has shifted pillar-side puts lateral load on the operator mounting bracket. The bolts hold, but the stone or brick around the bracket does not. We weld a larger backer plate and set deeper anchors to spread the load across more masonry surface.
- Underground operators failing after freeze-thaw cycles. Buried operators in Southlake are often installed near driveway drainage routes. The February 2021 freeze cracked more than a few control board housings, and freeze-thaw cycling keeps doing it. When the housing cracks, the board shorts, and the homeowner is left swinging a 700-pound gate by hand.
Pricing for Gate Parts & Welding in Southlake, TX
You should know what this work costs before you pick up the phone. In Southlake, hinge replacement on a standard ornamental swing gate runs $220 to $480 per hinge assembly, depending on pillar condition and gate weight. Crack repair and re-welding typically lands between $180 and $350. Full post replacement with concrete footing starts around $450 and runs to $900 for larger masonry columns. Custom fabrication, such as matching pickets or scrollwork, runs $150 to $400 per section depending on complexity.
Those are honest ranges for Southlake’s housing stock, not national averages. The number you get from us is the number on the invoice. We quote upfront, in writing, before a single bolt is turned. Call (432) 237-4128 for a free estimate.
We Also Serve Cities Near Southlake
We work throughout the Southlake area and regularly serve Gate Parts & Welding in Southlake as well as nearby Colleyville, Grapevine, Bedford, and Keller. Wherever the job is, the standard is the same: written price, done right, backed for 90 days.
Serving Southlake, TX - Our Local Coverage Area
We’re based in the Southlake area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Parts & Welding in Southlake
In Southlake, a leaning brick gate pillar is almost always a footing and soil problem, not a hinge problem by itself. The Blackland Prairie clay under the footing expands and contracts with wet and dry cycles, slowly heaving the entire pillar out of plumb. The hinge is just the first casualty: as the pillar leans, the hinge plate pulls away from the brick and the anchor bolts strip. We inspect both the pillar footing and the hinge mounting face before we recommend a fix. Some jobs only need re-anchoring. Others need the pillar footer rebuilt or the column re-set. Call (432) 237-4128 and we will tell you which one you have.
A mid-rail crack on a Southlake ornamental gate usually means rust, not impact. Water collects where the rail intersects the pickets, and once the protective coating is thin from age or irrigation overspray, the steel rots from the inside. The weakest point is the original weld, so that is where the crack shows first. The hinge area stayed intact because the load never shifted there. We grind the bad weld out, cut back the rusted section, and splice in new rail stock with a full penetration weld before coating the repair to match the rest of the gate.
Yes. We do not weld directly to stone. We weld or fabricate a steel backer plate sized to spread the operator load across as much masonry face as possible, then anchor the plate with Gate Access Control in Southlake expansion anchors set into the stone or mortar bed. The operator bracket bolts to that plate. This keeps the stone intact and gives the opener a solid base. On Southlake’s heavy ornamental gates, we often go one step further: a larger plate than the original install used, because the clay soil loads the operator harder here than in stable soil.
No. Fast hinge pin wear on a heavy Southlake dual-swing gate is a sign that the gate is out of alignment or that the hinges are undersized for the gate’s weight. When a pillar shifts and the gate hangs slightly off-plumb, the full gate weight concentrates on one corner of each hinge pin, chewing through the bushing in a fraction of its normal life. We correct the gate alignment and often upgrade to a heavier hinge with a greaseable bearing, sized for the actual leaf weight. A properly hung Southlake gate should run a decade or more between hinge replacements.
If the arm moves manually but the operator will not drive it, the first thing we check on Southlake gates is the limit switch and the control board. The 2021 freeze cracked control board housings on buried and surface-mount operators across the area, and moisture intrusion after the thaw shorted more boards than anyone wants to admit. Ice can also knock the limit settings out, so the board thinks the gate is already open or closed. A broken gear would grind or bind when you push the arm manually. Yours moves free, so it is probably not a gear. We can diagnose it over the phone at (432) 237-4128 before we ever roll a truck.
Written by Victor Salinas, Owner at Ironworks Gate Co., serving Southlake and the surrounding area with gate parts and welding expertise for over 42 years.