Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Parts & Welding Across Keller
When a driveway gate in Keller stops closing or sags off its hinges, the real problem is rarely what it appears to be. Most of the gate components we replace in Keller are failing for the same underlying reason: the shrink-swell clay under Tarrant County shifts with every drought and wet season, moving posts a fraction of an inch at a time. That movement pulls hinges out of alignment, cracks weld joints, and destroys operators that would otherwise last a decade. We have been fixing these exact failures for over 42 years, and we know Keller’s neighborhoods and HOAs well enough to fix the root cause the first time. Call (432) 237-4128 and a real person will answer, any hour, any day.
Why Ironworks Gate Co. Is Keller’s Preferred Gate Parts & Welding Company
Keller homeowners tell us the same story again and again: they paid for an operator replacement, the gate worked for a season, and then it started binding again. The operator was never the problem. The post had moved. We have spent decades in Tarrant County learning what actually fails on ornamental iron and steel gates, and in Keller’s HOA subdivisions built between 1993 and 2015, the pattern is remarkably consistent. A swing gate post that leans outward just three-quarters of an inch will strain a brand-new LiftMaster or Elite operator until the gears wear out. We find this all the time in neighborhoods around the 76248 and 76244 zip codes. Our Gate Parts & Welding team lets the work speak: correct diagnosis, honest write-up, and a fix that holds.
We are not the cheapest shop in Keller. We are the shop you call when you’re tired of paying for the same repair twice. Every job we complete carries our 90-Day Done Right Promise in writing. If something is not right after we leave, we come back and make it right. No arguing, no paperwork, no exceptions. Victor Salinas set the standard early: background-checked, uniformed technicians who treat a customer’s yard the way they would treat their own mother’s. That is the K.E.Y.S. code we still work by: Krafted right, Every time, Your home first, Standing behind it.
Keller sits in one of the most HOA-dense corridors in Tarrant County, and that changes how gate work gets done. Architectural committees review gate style, height, finish, and hardware before a single weld is laid. We know the approval pipeline, we build to submitted specs, and we coordinate with management companies when a shared community entry gate needs work. If you live in a neighborhood with a private, HOA-maintained entrance, you already know that a broken gate is not just your problem. It is everyone’s. We get that, and we schedule work in Keller so everyday resident access stays intact while we repair the parts that failed.
Our Gate Parts & Welding Services in Keller
Hinge Replacement
Hinges carry the full weight of an ornamental steel gate, and in Keller they carry that weight on moving clay. When a hinge post leans, the hinge pin binds and the leaf galls, and every cycle of the operator scrapes metal over metal. We stock heavy-gauge weld-on and bolt-on hinges sized for the larger, heavier gates common in Keller’s upscale subdivisions, including the estates around the Estates of Kensington and similar communities. We replace the hinge, re-align the leaf, and if the post itself has shifted, we reset it so the new hinge isn’t doomed to the same fate.
Post Replacement
This is the repair that saves Keller homeowners the most money over time. Drought summers contract the black clay and drop posts. Wet winters heave them back up. After ten or fifteen seasonal cycles, a post set in a shallow footing is leaning enough to bind the operator arm, no matter how new the motor is. We cut out the failed post, dig a deeper footing, set a heavier post in reinforced concrete, and weld the gate hardware back to plumb. It’s real work, but it will last thirty years, not three.
Rail Repair
Slide gates in Keller take a beating from that same soil movement. When one end of the track settles, the gate rail rides crooked and the rollers dig in. Rail sections crack at the welds, rust blooms inside the tube, and the gate starts dragging across the drive. We repair or replace bottom rails, top rails, and pickets, matching the original steel profile and finish so the repair passes HOA inspection the first time. If you’re in the 76244 area and your slide gate has been scraping, the rail is the first thing we check, not the operator.
Custom Welding
Keller HOAs are specific about what a gate is supposed to look like, and we fabricate to printed specs. That includes ornamental scrollwork, finials, spears, and frame sections that match a gate originally built in 1998 or 2005. We repair cracked heat-affected zones with proper preheat and full-penetration welds, not spot welds that crack again in two seasons. If your HOA says the gate must match the original approved plan, bring us the plan. We will match it, down to the finish.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Keller
Many Keller gates run on Elite, FAAC, LiftMaster, and Mighty Mule operators, and we are equipped on all of them. That matters more than you’d think. A technician who only knows one brand will replace a whole operator because a specific control board is throwing a fault code. Our techs read the code, diagnose the actual failed component, and replace the part instead of the whole unit. For Keller customers with boom-era automation, that single distinction can cut a repair bill from over a thousand dollars down to a few hundred. We keep common boards, remotes, and safety edges for Keller’s most common operator brands in our Dallas-Fort Worth service vehicles, which lets most Keller repairs happen in a single visit.
Common Gate Parts & Welding Problems We See in Keller Homes
- Clay-driven post lean on swing gates. This is Keller’s signature failure. The hinge post tilts outward over a decade of drought-wet cycles, the operator arm starts binding, and the gears take the damage. Replacing the operator without resetting the post just moves the countdown to the next failure.
- Cracked welds at the heat-affected zone. Ornamental steel gates in Keller HOA neighborhoods were sometimes welded to posts that were undersized for the gate weight. After years of soil movement and wind load, the steel cracks right at the weld edge. A proper repair requires grinding out the old weld, preheating, and rebuilding the joint with full penetration.
- Seized rollers and latch hardware. Wet winters in Tarrant County drive moisture into roller bearings and latch slides. By February, Keller slide gates are sticking, dragging, or completely off the track. We replace rollers with sealed-bearing units and swap latch hardware that was never meant to survive Texas clay-country drainage.
- HOA-mandated fixes that don’t address the root cause. Many Keller homeowners have paid twice for operator replacements because a previous repair only addressed the visible symptom. Our free second opinion on any written estimate exists precisely so you can find out whether you actually need the operator or just the post that’s moving under it.
Pricing for Gate Parts & Welding in Keller, TX
We quote every Keller job before any work begins, and the price is settled then. Not after. Not when we discover “one more thing.” The quote is the price. For reference, a typical hinge replacement on a residential swing gate in Keller runs $180 to $380 depending on gate weight and hinge count. Post replacement with a deeper concrete footing usually runs $400 to $900, more if the post is structural for a long slide gate. Custom welding repairs on cracked ornamental steel typically fall between $150 and $500, depending on the number of cracked sections and the finish work needed. Restoring a full gate with rail, hinge, and post work in Keller is commonly $800 to $1,500. We offer a free second opinion on any written estimate and $50 off any repair over $250. Call (432) 237-4128 and we will give you a straight number, not a range that moves when we get to the driveway.
We Also Serve Cities Near Keller
Our Keller service area extends into North Richland Hills, Southlake, Colleyville, and Hurst, where the same clay soil and HOA-governed gate styles drive the same repair patterns. If you’re just over the city line, we will get there. The diagnosis method stays identical whether we’re resetting a post in Keller or the next town over: find the moving part, fix the part that’s moving, and stand behind it in writing.
Serving Keller, TX - Our Local Coverage Area
We’re based in the Keller area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Parts & Welding in Keller
Yes. We fabricate to printed HOA specs, including material, rail profile, picket spacing, height, and finish. Bring us the approval document or the original gate plan, and we will build to it. Keller’s architectural committees are careful about consistency, and our custom welding work has passed many of them. Call (432) 237-4128 if you want us to look at the specs before you submit.
In Keller, usually yes. A post that leans outward just an inch puts constant lateral load on the operator arm, and that load chews through gearboxes and motors regardless of brand. We check post plumb on every binding-gate call in the 76248 and 76244 zips, because clay movement is the single most common root cause. It is also the repair that makes the new operator actually last. Call (432) 237-4128 and our tech will check the post before anyone sells you another motor.
Yes. We stage shared community entry gate work so the gate stays operational while we replace hinges, rollers, and rail sections. For Keller communities with a single point of entry, we work in phases and coordinate with the property manager so residents are not locked out or left with an open, unmanned gate. We know these systems are load-bearing for the whole neighborhood, not just one driveway. Call (432) 237-4128 to schedule a site walk.
Almost always, yes. Keller gates from the late 1990s and 2000s are typically heavy ornamental steel with decades of life left. The failure points are the moving parts and the posts, not the structural steel. Replacing hinges, rollers, and resetting posts on a fleet of gates is a fraction of the cost of replacing the gates themselves, and the HOA usually prefers repairs that match the original aesthetic. Get a quote before you replace anything. Call (432) 237-4128.
Yes, and it is one of the most common welding repairs we perform in Keller. Cracks near the hinge are almost always a symptom of a post that has moved and loaded the hinge in a direction it was never designed to carry. We grind out the crack, preheat the steel, rebuild the joint with full-penetration weld, and then address the post alignment so the new weld is not cracked again in two seasons. This is exactly the kind of repair a handyman patch job will not survive. Call (432) 237-4128 and we will look at it before you pay anyone else to touch it.
Call Ironworks Gate Co. for Gate Parts & Welding in Keller
If your gate sags, binds, drags, or has cracked steel near the hinges, call (432) 237-4128. A live person answers, every time. We will dispatch a uniformed technician to Keller, diagnose the work, and give you a written price before any bolt is turned. Victor Salinas and the rest of us at Ironworks Gate Co. have spent 42 years earning the right to say it: done right, and backed in writing. If it is not right, we come back. Every time, on every job.
Written by Victor Salinas, Owner at Ironworks Gate Co., serving Keller and the surrounding Tarrant County communities.