Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Parts & Welding Across Bedford
If you’re standing in your driveway in Bedford, TX looking at a gate that leans, drags, or will not close, the problem is rarely the latch you keep tightening. It is almost always the post under it, the hinge pulling free, or the frame that has twisted out of square. Gate parts and welding in Bedford is not a hardware-swap job. It is a structural repair, and it needs a company that understands exactly what 40 years of Blackland Prairie clay does to a cedar gate. We are Ironworks Gate Co., and we have been doing this work for over 42 years. Call (432) 237-4128 and we will send a technician who knows Bedford’s gates, Bedford’s soil, and Bedford’s trees.
Why Ironworks Gate Co. Is Bedford’s Preferred Gate Parts & Welding Company
Bedford homeowners do not call us for a quick patch. They call us because the last repair did not hold, and they want the job done once. Our Gate Parts & Welding team works on the actual structure: the post in the ground, the hinge bolted to the post, the frame the boards hang from. We are not a handyman service that also does gates. Gates are all we do. That focus shows up in how we diagnose a sagging gate in the Shady Brook neighborhood or a dragging rail near Generations Park: we check the post plumb first, before we touch a hinge.
Every job is protected by the 90-Day Done Right Promise. That is a written guarantee. If the repair does not hold, we come back and make it right. No paperwork, no argument, no exceptions. Victor Salinas leads our crews, and he holds every technician to the same standard: Krafted right, Every time, Your home first, Standing behind it. We answer the phone 24 hours a day, 7 days a week. When a Bedford gate fails on a Saturday evening, you get a live person on the line, not a voicemail ending with “Monday.”
We coordinate dispatch and scheduling from our Dallas-Fort Worth office, so crews reach Bedford quickly and arrive with the right parts. That means hinge plates, post brackets, weld material, and operators are on the truck before we pull up. You will not wait two weeks for a second visit because somebody had to order a part.
Our Gate Parts & Welding Services in Bedford
We carry the parts and do the welding that Bedford’s older gates actually need. Here is how we handle the four most common calls.
Hinge Replacement
A hinge does not fail on its own. In Bedford, the hinge screw pulls out because the post wood has rotted or the post itself has tilted. We replace the hinge with a heavier pattern, but only after the post is addressed. If the post is sound, we set the new hinge with lag bolts longer than the originals and reinforce the wood around the screw holes. If the post is not sound, we tell you before we touch the hinge, because a new hinge in a bad post is just the same failure waiting to happen again.
Post Replacement
This is the dominant repair call across Bedford’s established neighborhoods, and for a reason most contractors miss. The expansive clay soil under Bedford shrinks during summer droughts and swells after rain, moving in cycles that have been torquing gate posts for decades. A post that was plumb in 1985 is now leaning six degrees toward the drive, and every hinge screwed into it is fighting that lean. We excavate, cut any roots that have pushed the post, set a new pressure-treated post in concrete, and wait for the concrete to cure before re-hanging the gate. Done this way, the repair lasts. Done the shortcut way, you call us again in a year.
Rail Repair
When a wooden gate sags, the top rail often splits at the point where the hinge bolts pass through. The wood has been carrying load it was never designed for, usually because the post moved. We remove the split section, scarf in new wood, and reinforce the joint with a steel plate where the design allows. Then we re-align the hinges so the load is distributed evenly. On gates where the rail has split repeatedly, we recommend a steel frame retrofit rather than another wood patch.
Custom Welding
Some Bedford gates were built to a standard size in 1980. Others were built for a wide driveway, a side yard, or a specific opening that no off-the-shelf part fits anymore. Our custom welding covers steel gate frames, reinforcing plates, hinge mounts, and brackets. We weld on site where the work allows, and fabricate in-shop when it does not. If your gate needs a steel skeleton under wood boards, or a new steel frame matched to your existing brick posts, we build it to fit the opening, not the catalog.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Bedford
When an operator or opener is involved, we service the brands Bedford homes actually have on their driveways: FAAC, BFT, Linear, and Viking among them. Our technicians are trained and equipped on nine major gate-automation brands, so the correct fix happens on the first visit, whether the issue is a limit switch, a photocell, or a board that has burned out from a gate binding against a displaced post. We stock common parts for Bedford’s most frequent operator failures, which shortens turnaround on repairs that would otherwise wait on a shipment.
Common Gate Parts & Welding Problems We See in Bedford Homes
These are the failures we see again and again in Bedford, and they are almost always structural, not cosmetic.
- Post footing heave and tilt: Bedford’s Blackland Prairie clay swells and shrinks with every wet-dry cycle, torquing post footings out of plumb. The post leans, the gate follows, and the hinge screws strip out of the wood.
- Root displacement from mature trees: In older interior Bedford neighborhoods, decades of growth from post oaks and elms have pushed surface roots sideways into fence lines. A root against a gate post will move that post inch by inch until the gate will not latch.
- Sagging panels splitting top rails: When the hinge post shifts even a few degrees, the panel’s top rail takes load it was never built for. The rail splits at the hinge bolts, and the gate drops until it drags on the drive.
- Operator burnout from binding gates: An automatic opener does not know the post tilted. It just tries harder until the motor overheats or the safety photocell trips repeatedly. The operator is not the problem; the post is. We fix both.
Pricing for Gate Parts & Welding in Bedford, TX
Here is what you can expect to pay for common repairs in Bedford.
- Hinge replacement: $120-$280 per hinge set, depending on gate weight and post condition.
- Post replacement (single gate post): $350-$700, including excavation, new post, concrete, and re-hanging.
- Rail repair with steel reinforcement: $180-$420, depending on the split length and whether we are scarfing in new wood or adding a steel plate.
- Custom welding (on-site, small job): $200-$500. Full steel frame retrofits run higher and are quoted after we measure the gate.
The price we quote is the price you pay. We settle the number before a single bolt is turned. You will get a written estimate, and if you already have a written estimate from another company, ask about our Free Second Opinion. We will review it honestly. Call (432) 237-4128 for an exact quote on your Bedford gate; estimates are free.
We Also Serve Cities Near Bedford
Our crews work throughout the Mid-Cities and the surrounding area. If you live in Colleyville, Hurst, Euless, or North Richland Hills, the same Gate Parts & Welding in Bedford team covers your neighborhood too. The clay, the trees, and the aging gates do not stop at the city line, and neither do we.
Serving Bedford, TX - Our Local Coverage Area
We’re based in the Bedford area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Parts & Welding in Bedford
Because the hinge is not the root cause. In Bedford, the expansive clay under your gate post has been heaving and tilting that post for decades. New hinges in a leaning post will sag again within a year. The fix is resetting or replacing the post, then re-hanging the gate with hinges sized for the actual load. Call (432) 237-4128 and we will check the post plumb first, before we sell you another hinge set.
Yes. We do this for Bedford homeowners who want to keep their existing wood boards but need the structural spine replaced. We build a steel frame matched to your gate’s dimensions, weld the hinge mounts and latch points onto it, and reattach the boards. It is a measured job with a written price, not a same-day repair. Call (432) 237-4128 and we will come measure and quote it free.
If the motor runs but the gate does not move, the common causes are a broken drive chain, a stripped gear in the operator, or a wheel off its track. On Bedford slide gates, we also see the problem where the track itself has shifted in the clay, so the gate binds and the motor cannot pull it. We diagnose the operator and the track in the same visit, because fixing one without checking the other is how you end up with a second service call.
Not necessarily. Solar makes sense when the distance from the house to the gate makes trenching power impractical or too expensive. We install and service solar openers from brands like FAAC and Viking. We will look at the shade from your trees, the panel exposure, and the gate’s daily cycle count before recommending solar over a power run. Estimates are free. Call (432) 237-4128.
In almost every case, yes. We excavate the post, cut the specific root that is pushing the footing, set a new post in concrete, and leave the tree standing. Removing one lateral root will not kill a mature post oak. We have done exactly this work in Bedford’s older neighborhoods where roots and fence lines have been sharing ground for 40 years, and the tree comes through fine. Call (432) 237-4128 and we will look at the root situation before quoting the post work.
Need a gate post fixed, a hinge rebuilt, or a steel frame welded onto an old wooden gate in Bedford? Call Ironworks Gate Co. at (432) 237-4128. We will quote the price before we start, send a technician who does this work every day, and stand behind the repair in writing with the 90-Day Done Right Promise. Victor Salinas and our crews have been doing gates for over 42 years, and we plan to be doing them in Bedford for another forty.
Written by Victor Salinas, Owner at Ironworks Gate Co.