Gate Repair in Hurst - Same-Day Repair, Priced Before We Start

Fast, Reliable Gate Repair Across Hurst

A leaning gate in Hurst is rarely just a hinge problem. Most of the repair calls we take from the 76053 and 76054 zip codes trace back to one thing: the expansive clay soil under this part of the Blackland Prairie. It heaves posts out of plumb, binds hinges, and makes a gate drag hard against the driveway. We fix that at the source, not just at the surface. If your gate is sagging, sticking, or sitting cockeyed on its posts, call us at (432) 237-4128. We serve Hurst homeowners directly, and a live person answers every call, day or night.

Call (432) 237-4128

Why Ironworks Gate Co. Is Hurst’s Preferred Gate Repair Company

Our crews work in Hurst every week. We know the older subdivisions along Brown Trail, the brick ranches tucked into the neighborhoods off Precinct Line Road, and the particular way a 1960s-era wrought iron gate behaves after fifty years of clay movement. That local knowledge matters. A technician who has only worked on newer construction might replace a hinge and call it done. We check the post first. In Hurst, the post is usually the problem.

Homeowners here tend to keep their homes for decades. So do we. Ironworks Gate Co. has been at this for over 42 years, and our technicians arrive background-checked and uniformed, working in your driveway the way they would work in their own mother’s. Every job ends with a written 90-Day Done Right Promise. Not a verbal assurance. A written guarantee: if it’s not right, we come back and make it right. No paperwork, no arguing. Victor Salinas leads our team, and that standard is his rule.

Our Gate Repair Services in Hurst

Hinge & Post Repair

In Hurst, hinge repair almost always means post repair. When expansive clay heaves a concrete post even two or three inches, the hinge geometry changes and the gate starts to bind, drag, or refuse to latch. We excavate the original footing, drill a bell-bottom pier below the active clay line, and re-set the post so it stays put. Then we rebuild the hinge pocket and hang the gate square. It’s a proper structural fix, not a shim and a prayer.

Gate Realignment

A gate that sags into the driveway or scrapes against the post is telling you something about the ground it sits on. Hurst’s wet-dry cycles move soil faster than most people expect, and a gate that was plumb two years ago can be three inches out today. We re-plumb the posts, reset the hardware, and restore the gate’s swing so it closes like the day it was hung. If the iron itself is still sound, realignment is often all the job requires.

Electric Gate Repair

Automatic gates on older Hurst homes frequently run on control boards from the 1970s and 80s. Those boards predate modern entrapment protection, and North Texas power surges knock them out with some regularity. We diagnose the board, the receiver, the photo eyes, and the limit switches, then tell you honestly whether a retrofit makes sense or a new operator is the cheaper long-term answer. We’re trained and equipped on nine major automation brands, including LiftMaster, FAAC, Elite, and Mighty Mule.

Weld & Rust Repair

Wrought iron gates in Hurst have spent decades in North Texas heat. That means expansion and contraction cycles that stress every weld, especially at the hinge collar where the gate’s full weight concentrates. When a weld cracks there, the gate sags suddenly or tears loose from the post. We grind out the failed weld, re-weld with proper penetration, and reinforce the area so it doesn’t fail again next season. Rust through at the hinge collar gets cut out and replaced with new steel before re-hanging.

If you’re not sure which service you need, call (432) 237-4128 and describe what the gate is doing. We’ll tell you what we think over the phone, then schedule a visit to confirm it in person.

Trusted Brands We Service in Hurst

Whatever opener is on your driveway, we likely work on it every week. Our technicians carry parts for LiftMaster, FAAC, Elite, Mighty Mule, and the other major brands on their trucks, so most Hurst repairs are completed in a single visit. We stock replacement control boards, limit switches, photo eyes, and remote receivers for the older models still common on mid-century homes here. If your operator predates modern safety features, we’ll walk you through what a retrofitted safety package involves and what it costs before any work begins.

Common Gate Repair Problems We See in Hurst Homes

• Heaved concrete posts. The expansive clay under Hurst swells when wet and shrinks when dry, lifting gate posts out of the ground and out of plumb. The post may be structurally fine while sitting three to five inches off vertical. The fix is re-setting it below the active clay line, not replacing the gate.
• Cracked welds at the hinge collar. Decades of North Texas heat cycles flex the metal at its stress point until the weld fails. The gate sags suddenly, sometimes within a single summer. We open the crack, re-weld, and reinforce.
• Obsolete operator boards. 1970s-era control boards lack modern entrapment protection and are vulnerable to power surges. The gate goes dead and stays dead. A replacement board or a full operator retrofit gets it moving again.
• Rust-through at the bottom rail and hinge collar. Wrought iron from the 1960s and 70s often rusts from the inside out, especially where sprinkler water and clay soil moisture sit against the metal. We cut out the compromised section and weld in new steel, then rust-treat and prime.

Pricing for Gate Repair in Hurst, TX

We Also Serve Cities Near Hurst

Our crews work throughout the Mid-Cities and the surrounding area. If you’re in Bedford, North Richland Hills, Colleyville, or Euless, we’re close by and we know those neighborhoods too. Our Gate Repair team covers the full metro, and Hurst is one of the communities we know best. Call us and we’ll have someone out to look at your gate.

FAQs - Gate Repair in Hurst